LIMITED TIME ONLY for new customers: 15% off your first repair order!

Part Details

A06B-6064-H308#H521 SPINDLE AMP AC SP-8S SERIAL

FANUC parts >> A06B-6064-H308#H521 SPINDLE AMP AC SP-8S SERIAL

Part Name: SPINDLE AMP AC SP-8S SERIAL

Part Number: A06B-6064-H308#H521

Contact Us

For parts repair or replacement, please fill out the form below and we’ll get back to you as soon as possible.

upload pdf

* Indicates a Required Field

Exchange Price

$4000

OUT OF STOCK
Non return of a repairable exchange part within 15 days will result in an additional invoice for the above exchange price.

Repair Price

$3680

Turnaround times for standard repairs are based on workload. Please contact Tri Star CNC services for emergency repair requirements.
Please contact Tri Star CNC Services to place an order.

SPINDLE AMP AC SP-8S SERIAL

Alarm & error codes

When a FANUC serial spindle amplifier alarm is thrown chances are you'll need support from professionals experienced in FANUC component repairs. Give us a call - phone support is FREE and we'll clearly define your options for parts repair or replacement:

Alarm CodeDescription
01 Spindle motor over temp.
02 Actual motor speed is largely deviated from the commanded speed.
03 DC link fuse has blown.
04 Detected that the 3-phase input has an open phase.
05 Control power supply fuse blown.
07 The motor rotates at a speed exceeding 115% (standard setting) of the maximum allowable speed.
08 High input voltage.
09 Heat sink is overheated.
10 Input power voltage dropped.
11 DC link voltage was excessively high.
12 Excessively large current flowed into the DC link of the main circuit.
13 Memory inside the CPU is faulty.
15 Spindle switch/output switch sequence faulty.
16 The memory (RAM) is faulty.
18 ROM is defective.
19 The offset voltage of the phase U current detection circuit is excessively high.
20 The offset voltage of the phase V current detection circuit is excessively high.
24 The power to the CNC is turned off. (This symptom does not represent an error.) Serial communication data transferred between the CNC and spindle amplifier module contains an error.
25 Serial transfer data error.
26 The sensor signal (for speed control) for Cs contour control has an error.
27 The sensor signal (position coder signal) for position control is abnormal.
28 The sensor signal (for position control) for Cs contour control is abnormal.
29 An excessive load (standard setting: load meter reading of 9 V) has been applied continuously for a certain period (standard setting: 30 seconds).
30 Defective power regeneration circuit.
31 The motor failed to rotate as specified, and has stopped or is rotating at a very low speed.
32 LSI memory for serial communication is abnormal. A check is made when the power is turned on.
33 DC link circuit problem.
34 Incorrect parameter setting.
35 The gear ratio set in a parameter exceeds the value range allowable for internal processing.
36 Error counter over flow.
37 Incorrect parameter setting for the number of speed feedback pulses.
39 Incorrect data ROM type for Cs contour control detector circuit or incorrect setting.
40 The one-rotation signal for Cs contour control is not generated.
41 Incorrect setting of parameter of number of position coder signal pulses.
42 Alarm for indicating position coder 1 -rotation signal not detected.
43 Alarm for indicating disconnection of position coder signal for differential speed mode.
46 Alarm for indicating failure in detecting position coder 1 -rotation signal in thread cutting operation.
47 Incorrect setting of parameter for number of position coder signal pulses.
48 Position coder 1 -rotation signal abnormality.
49 The converted differential speed is too high.
50 Excessive speed command calculation value in spindle synchronization control.
51 Undervoltage at DC link section.
52 ITP signal abnormality I.
53 ITP signal abnormality II.
54 Overload current alarm.
55 Power line abnormality in spindle switching/output switching.

Parts & Repair Warranty Information

Exchange parts and repaired parts include a 1-year warranty. Tri Star CNC, LLC warrants the COMPLETE ASSEMBLY REPAIR – not just the parts and labor.

Get more details on our warranty and please contact us for further support.

Contact Us

For parts repair or replacement, please fill out the form below and we’ll get back to you as soon as possible.

upload pdf

* Indicates a Required Field
Call now for FREE phone support
FREE Phone Support
815-578-9145