815-578-9145A02B-0198-B501 Power Mate F
FANUC parts >> A02B-0198-B501 Power Mate F
Part Name: Power Mate F
Part Number: A02B-0198-B501
Exchange Price
$1,439
Repair Price
$1,083
Powermate "F" #A02B-0198-B501
Tri Star CNC provides expert repair services for the A02B-0198-B501 Fanuc Powermate F controller. With nearly a century of experience between us and some of the most advanced diagnostic equipment available, our engineers and service technicians are able to quickly determine the cause for your Powermate Model "F" failure and perform all necessary FANUC repairs.
FA
NUC CNC Power Supply Repair and Replacement Services
Every part that enters our shop is thoroughly inspected and cleaned. To get started, fill out an RMA form and send it along with a contact form. We keep spare parts that are ready for exchange so you can keep your operations running while you wait for your repaired part to return. If your part is beyond repair or you need a spare, we offer replacement parts in our shop. Contact us to begin the purchase process.
We also repair other FANUC parts. View our full list of services:
FANUC Servo Alarm Codes
If your A02B-0168-B053 servo is showing an error code, first check our list of FANUC servo alarm codes.
| Alarm Code | Message | Description |
|---|---|---|
|
PSM-5.5 to PSM-11 |
The main circuit power module (IPM) has detected an overload, overcurrent, or control supply voltage decrease, overcurrent, or control supply voltage decrease. Internal cooling circuit failure, Overload, Input supply voltage imbalance, IPM failure, or control supply voltage decrease of the power module. |
|
|
PSM-15 to PSM-55 |
Overcurrent flowed into the input of the main circuit. Input supply voltage imbalance, IGBT defective. |
|
|
N/A |
Internal cooling circuit faulty. |
|
|
N/A |
The temperature of the heat sink has risen. |
|
|
N/A |
DC voltage (DC link) has dropped |
|
|
N/A |
The input power supply is abnormal (open phase) or the main circuit capacitor was not recharged within the specified time. |
|
|
N/A |
The input power supply is abnormal (open phase). |
|
|
N/A |
The DC link voltage is abnormally high. |
|
|
N/A |
The offset of the current detection circuit of the main circuit DC link is excessive. |
|
|
PSMR |
The regenerative discharge unit is heated. |
|
|
N/A |
The main circuit power supply has an open phase. |
|
|
N/A |
The DC link voltage is abnormally high. |
|
|
N/A |
An error occurred in internal parameter data transfer processing. |
|
|
N/A |
The frequency of the main circuit input power supply is abnormal. |
|
|
N/A |
The input power supply of the main circuit has an imbalance. |
|
|
N/A |
When the magnetic contactor is turned on, the phase sequence of the power supply cannot be determined. |
|
|
N/A |
Internal cooling circuit faulty. |
|
|
N/A |
ROM is faulty. |
|
|
N/A |
RAM is faulty |
|
|
N/A |
A program is not operating normally. |
|
|
N/A |
The input power supply is abnormal (open phase). |
|
|
N/A |
The temperature of the regenerative resistor has arisen abnormally |
Additional Repairs
Contact our GE FANUC CNC Controller repair and replacement specialists for more information on service options for the A02B-0198-B501.
Parts & Repair Warranty Information
Exchange parts and repaired parts include a 1-year warranty. Tri Star CNC, LLC warrants the COMPLETE ASSEMBLY REPAIR – not just the parts and labor.
Call now for FREE phone support